الصفحة الرئيسية > الدوائر المتكاملة الدوائر المتكاملة > SN74LS148N

SN74LS148N

8-to-3 priority encoder, active-low, cascade EI/EO/GS, LS TTL, PDIP-16

4500

المخزون الفعال

انتقل إلى الاستفسار

Image for reference only

جزء الشركة المصنعة ： جزء الشركة المصنعة

SN74LS148N

الحزمة ： الحزمة

PDIP-16 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

العلامة التجارية ： العلامة التجارية

فئات المنتجات:：فئات المنتجات

الدوائر المتكاملة الدوائر المتكاملة, واجهة ICs

توصيات أخرى قد تكون مهتماً بها.

SII9396SCNUC-BAR

IS43TR16256BL-125KBLI

الوصف

نظرة عامة على المنتج

The SN74LS148N is an 8-line to 3-line priority encoder from Texas Instruments with active-low inputs/outputs, cascading capability, and group signal outputs in a 16-pin PDIP package.

المواصفات الرئيسية

الوظيفة	8-line to 3-line priority encoder
عائلة المنطق	LS (Low-power Schottky)
جهد الإمداد	4.75V to 5.25V (5V nominal)
Inputs	8 active-low (0-7), 1 enable (EI, active-low)
Outputs	3 active-low (A2, A1, A0), GS, EO
Priority	Input 7 is highest priority
تأخير الانتشار	15ns typical (data to output)
Enable Input (EI)	Active-low (device enabled when EI=LOW)
Group Signal (GS)	Active-low (asserted when any input is active)
Enable Output (EO)	Active-low (asserted when no input is active)
درجة حرارة التشغيل	0°C to +70°C
الحزمة	PDIP-16 (19.3 x 6.35mm)

الميزات

8-line to 3-line priority encoder with active-low I/O
Priority: input 7 has highest, input 0 lowest
Cascading via EI and EO for expanded encoding
Group signal (GS) indicates at least one active input
Enable input (EI) for device selection
Standard 74LS148 pinout

التطبيقات

Keyboard encoding
Interrupt vector generation
Priority interrupt encoding for CPUs
Data compression and encoding
Cascaded multi-chip encoding systems

مقدمة المنتج:SN74LS148N مقدمة المنتج

The SN74LS148N from Texas Instruments is an 8-line to 3-line priority encoder that converts one of eight active-low input lines to a 3-bit binary output code. When multiple inputs are active simultaneously, the encoder outputs the code for the highest-priority input (input 7 is highest, input 0 is lowest). All inputs and outputs are active-low, simplifying connection to microprocessor interrupt systems that use active-low signals. The enable input (EI, active-low) activates the device; when EI is HIGH, all outputs are HIGH (inactive). The group signal (GS) output goes LOW when any input is active and the device is enabled, indicating a valid encoded output. The enable output (EO) goes LOW only when no inputs are active and the device is enabled. GS and EO facilitate cascading: for a 16-to-4 encoder, two 148s are used with the lower-priority device’s EO connected to the higher-priority device’s EI. The N suffix denotes the PDIP-16 through-hole package.

مبدأ العمل:SN74LS148N مبدأ العمل

The SN74LS148N continuously evaluates the eight input lines (0-7, active-low). If input 7 is LOW (active), the outputs A2,A1,A0 = L,L,L (binary 7, active-low encoded as 000) regardless of the states of inputs 0-6. If input 7 is HIGH (inactive) and input 6 is LOW, the outputs = L,L,H (binary 6). This priority chain continues down to input 0, which only gets encoded if no higher-priority input is active. When the enable input (EI) is HIGH, the device is disabled: all data outputs (A0-A2) are HIGH, GS is HIGH, and EO is HIGH. When EI is LOW and at least one input is active, GS = LOW (indicating a valid encoding) and EO = HIGH. When EI is LOW and no inputs are active, GS = HIGH and EO = LOW. For cascading two devices to create a 16-to-4 encoder: the higher-priority device (inputs 8-15) has its EI connected to the system enable, and its EO connected to the lower-priority device’s EI. The GS outputs of both devices are NANDed to form the MSB (A3) of the 4-bit output. The A0-A2 outputs of both devices are ORed (wire-AND for active-low) to form the lower 3 bits.

وصف الدبوس:SN74LS148N تعريف الدبوس ووظائفه

دبوس	الاسم	النوع	الوصف
1	4	المدخلات	Input line 4 (active low)
2	5	المدخلات	Input line 5 (active low)
3	6	المدخلات	Input line 6 (active low)
4	7	المدخلات	Input line 7 (active low, highest priority)
5	EO	المخرجات	Enable output (active low, =LOW when no input active)
6	GS	المخرجات	Group signal (active low, =LOW when any input active)
7	A2	المخرجات	Encoded output MSB (active low)
8	GND	الطاقة	أرضي
9	A1	المخرجات	Encoded output middle bit (active low)
10	A0	المخرجات	Encoded output LSB (active low)
11	0	المدخلات	Input line 0 (active low, lowest priority)
12	1	المدخلات	Input line 1 (active low)
13	2	المدخلات	Input line 2 (active low)
14	3	المدخلات	Input line 3 (active low)
15	EL	المدخلات	Enable input (active low)
16	VCC	الطاقة	Supply (4.75V to 5.25V)

Application Scenarios:In which products and applications isSN74LS148N مستعمل

Interrupt Encoder: 8 interrupt sources into 3-bit vector; GS connects to MCU /IRQ pin; A0-A2 read as interrupt ID
Keyboard Encoder: 8 keys into 3-bit code; priority resolves simultaneous key presses
16-Input Encoder: Cascade two 148s for 16-to-4 encoding; higher-priority EO drives lower EI
Priority Detection: GS output indicates any request; MCU reads A0-A2 only when GS=LOW
Data Compression: Encode 8 binary inputs into 3 bits for bus width reduction

Alternative Models:What chips are recommended as replacements for SN74LS148N

الطراز	الشركة المصنعة	الفرق الرئيسي	الحزمة	Supply
74LS148N	TI/Nexperia	Original TTL version with 5V-only supply, typical propagation delay 10-15ns	DIP-16	5V TTL
74LS148D	TI/Nexperia	Surface-mount SOIC version of LS with identical logic function	SOIC-16	5V TTL
74HC148D	TI/Nexperia	CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity	SOIC-16	2-6V CMOS
74HC148N	TI/Nexperia	Through-hole DIP version of HC family for prototyping and repair	DIP-16	2-6V CMOS
74HCT148D	TI/Nexperia	CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V	SOIC-16	4.5-5.5V TTL-in
74HCT148N	TI/Nexperia	Through-hole DIP version of HCT family for prototyping and repair	DIP-16	4.5-5.5V TTL-in

The 74148 is a 8-Line to 3-Line Priority Encoder. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.