الصفحة الرئيسية > الدوائر المتكاملة الدوائر المتكاملة > SN74LS32N

SN74LS32N

Quad 2-input OR gate, LS TTL, 14ns, PDIP-14

7000

المخزون الفعال

انتقل إلى الاستفسار

Image for reference only

جزء الشركة المصنعة ： جزء الشركة المصنعة

SN74LS32N

الحزمة ： الحزمة

PDIP-14 (19.3 x 6.35 x 4.57mm, 2.54mm pitch, through-hole)

العلامة التجارية ： العلامة التجارية

فئات المنتجات:：فئات المنتجات

الدوائر المتكاملة الدوائر المتكاملة, واجهة ICs

توصيات أخرى قد تكون مهتماً بها.

SII9396SCNUC-BAR

IS43TR16256BL-125KBLI

الوصف

نظرة عامة على المنتج

The SN74LS32N from Texas Instruments is a quad 2-input positive OR gate with LS TTL technology, 14ns propagation delay, and industry-standard 7432 pinout in a 14-pin PDIP package.

المواصفات الرئيسية

Number of Gates	4 (quad 2-input OR)
عائلة المنطق	LS (Low-power Schottky)
جهد الإمداد	4.75V to 5.25V (5V nominal)
تأخير الانتشار	14ns typical @ 5V
Output Drive (IOL/IOH)	8mA / -0.4mA
درجة حرارة التشغيل	0°C to +70°C
الحزمة	PDIP-14 (19.3 x 6.35mm)

الميزات

Four independent 2-input OR gates
LS TTL technology
14ns typical propagation delay
Industry-standard 7432 pinout

التطبيقات

Signal combining (any-input-active detection)
Interrupt request lines
Error flag combination
Active-HIGH logic merging

مقدمة المنتج:SN74LS32N مقدمة المنتج

The SN74LS32N from Texas Instruments contains four independent 2-input OR gates in a 14-pin PDIP package. Each gate performs Y = A OR B; the output is HIGH when either or both inputs are HIGH, and LOW only when both inputs are LOW. The OR gate is the natural complement of the AND gate: while AND requires all inputs to be active, OR requires any input to be active. This makes the 7432 ideal for combining multiple active-HIGH signals: interrupt request lines, error flags, or enable signals. When any one of multiple sources needs to trigger an action, the OR gate combines them into a single output. The N suffix denotes the PDIP-14 through-hole package.

مبدأ العمل:SN74LS32N مبدأ العمل

Each OR gate in the SN74LS32N performs Y = A OR B. The truth table is: 00→0, 01→1, 10→1, 11→1. The output is HIGH when at least one input is HIGH. The OR can be constructed from NAND gates using DeMorgan’s theorem: A OR B = NOT(NOT-A AND NOT-B) = NAND(NAND(A,A), NAND(B,B)), but the dedicated 7432 is simpler and faster. For active-LOW signals (where LOW means active), use a NAND gate instead: if two active-LOW interrupt lines /INT1 and /INT2 need to be combined, NAND gives an active-LOW output when either input is LOW, which is the OR function in negative logic. The OR gate is also used in sum-of-products logic: A OR B = A+B in Boolean algebra, where + represents OR.

وصف الدبوس:SN74LS32N تعريف الدبوس ووظائفه

دبوس	الاسم	النوع	الوصف
1	1A	المدخلات	Gate 1 input A
2	1B	المدخلات	Gate 1 input B
3	1Y	المخرجات	Gate 1 output (OR)
4	2A	المدخلات	Gate 2 input A
5	2B	المدخلات	Gate 2 input B
6	2Y	المخرجات	Gate 2 output (OR)
7	GND	الطاقة	أرضي
8	3Y	المخرجات	Gate 3 output (OR)
9	3A	المدخلات	Gate 3 input A
10	3B	المدخلات	Gate 3 input B
11	4Y	المخرجات	Gate 4 output (OR)
12	4A	المدخلات	Gate 4 input A
13	4B	المدخلات	Gate 4 input B
14	VCC	الطاقة	Supply (4.75V to 5.25V)

Application Scenarios:In which products and applications isSN74LS32N مستعمل

Interrupt Combine: /INT1 and /INT2 are active-HIGH; OR combines them; any interrupt triggers MCU
Error Flag: Over-temp OR over-current OR over-voltage → single ERROR output; any fault triggers shutdown
Clock Select: CLK_A or CLK_B → single output; one at a time (mutually exclusive clocks)
Enable OR: Manual-enable OR software-enable; either one activates the circuit

Alternative Models:What chips are recommended as replacements for SN74LS32N

الطراز	الشركة المصنعة	الفرق الرئيسي	الحزمة	Supply
74LS32N	TI/Nexperia	Original TTL version with 5V-only supply, typical propagation delay 10-15ns	DIP-14	5V TTL
74LS32D	TI/Nexperia	Surface-mount SOIC version of LS with identical logic function	SOIC-14	5V TTL
74HC32D	TI/Nexperia	CMOS version with wide 2-6V supply range, lower power consumption and higher noise immunity	SOIC-14	2-6V CMOS
74HC32N	TI/Nexperia	Through-hole DIP version of HC family for prototyping and repair	DIP-14	2-6V CMOS
74HCT32D	TI/Nexperia	CMOS with TTL-compatible input levels, ideal for mixing with LS devices at 5V	SOIC-14	4.5-5.5V TTL-in
74HCT32N	TI/Nexperia	Through-hole DIP version of HCT family for prototyping and repair	DIP-14	4.5-5.5V TTL-in
74AC32D	TI/Nexperia	Advanced CMOS with 2-6V supply and higher output drive current (24mA vs 6mA for HC)	SOIC-14	2-6V CMOS
74AC32N	TI/Nexperia	Through-hole DIP version of AC family for prototyping and repair	DIP-14	2-6V CMOS
74LVC32D	TI/Nexperia	Low-voltage CMOS for 1.65-3.6V modern logic with 24mA output drive and bus-hold inputs	SOIC-14	1.65-3.6V CMOS
74LVC32N	TI/Nexperia	Through-hole DIP version of LVC family for prototyping and repair	DIP-14	1.65-3.6V CMOS

The 7432 is a Quad 2-Input OR Gate. Family variants span from the original LS TTL (5V only) to modern LVC/AUP (down to 0.8V). HC and HCT versions offer 2-6V CMOS operation with HCT providing TTL-compatible input thresholds for mixed 5V systems. CD4000-series equivalents offer the widest 3-18V supply range at the cost of lower switching speed. DIP packages (N suffix) are through-hole; SOIC (D suffix) and TSSOP are surface-mount.