The SN74LS145DR from Texas Instruments is a BCD-to-decimal decoder\/driver in a 16-pin SOIC (D) package with tape and reel packaging. Key specifications: decodes 4-bit BCD input (A, B, C, D) to 1-of-10 active-low outputs (0 through 9); open-collector NPN output transistors with 80 mA sink current capability per output; 15 V output breakdown voltage; all outputs are OFF for invalid BCD input conditions (10-15); low power dissipation 35 mW typical for LS variant; TTL and DTL compatible inputs; compatible for interfacing with most MOS integrated circuits; operates from a single 5 V supply (4.75 V to 5.25 V); operating temperature 0 to +70 degrees C (commercial grade); 16-pin SOIC package (9.9 x 6.0 mm). The device consists of eight inverters and ten four-input NAND gates. The inverters are connected in pairs to make BCD input data available for decoding by the NAND gates. The high-performance NPN output transistors are designed for use as indicator, relay, or open-collector logic-circuit drivers. MSL Level-1-260C-UNLIM. RoHS compliant. Active product status.<\/p>","protected":false},"excerpt":{"rendered":"
The SN74LS145DR from Texas Instruments is a BCD-to-decimal decoder\/driver in a 16-pin SOIC (D) package with tape and reel packaging. Key specifications: decodes 4-bit BCD input (A, B, C, D) to 1-of-10 active-low outputs (0 through 9); open-collector NPN output transistors with 80 mA sink current capability per output; 15 V output breakdown voltage; all […]<\/p>\n","protected":false},"author":2,"featured_media":2897,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[13,22],"tags":[],"chip_brand":[138],"class_list":["post-1980","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-integrated-circuits-ics","category-video-ics","chip_brand-ti"],"acf":{"brief_explanation":"BCD-to-decimal decoder\/driver, 4-bit input, 10 open-collector outputs, 80mA sink, 15V breakdown, SOIC-16, 0~70C","date_code":"","package_case":"SOIC-16 (D) (9.9 x 6.0 x 1.58 mm, 1.27mm pitch)","in_stock":20000,"datasheet":"https:\/\/www.ti.com\/product\/SN74LS145","price":"$0.45 (1K+ pcs)","product_introduction":"The SN74LS145DR from Texas Instruments is a BCD-to-decimal decoder\/driver that converts a 4-bit Binary-Coded Decimal (BCD) input into one of ten active-low outputs. It belongs to the venerable 74LS (Low-power Schottky) TTL logic family, which has been a workhorse of digital electronics since the 1970s.\n\nThe SN74LS145 is unique among standard logic decoder ICs because it combines decoding with driving capability. Unlike simple decoders such as the 74LS42 (BCD-to-decimal decoder without drive capability), the 74LS145 features high-performance NPN output transistors with 80 mA sink current capability and 15 V breakdown voltage. This makes it suitable for directly driving loads that standard logic outputs cannot handle, such as indicator lamps, relay coils, LEDs, and other medium-current loads.\n\nThe device accepts a 4-bit BCD input (D, C, B, A from most significant to least significant) and activates one of ten outputs (0 through 9) corresponding to the input value. The active output is driven LOW (sinking current), while all other outputs are OFF (open-collector, high impedance). For invalid BCD input codes (10 through 15, which are not valid decimal digits), all outputs are OFF, providing a natural blanking function.\n\nThe open-collector output configuration is essential for the driving applications this device was designed for. Each output is the collector of an NPN transistor that can sink up to 80 mA when turned on, and withstand up to 15 V when turned off. This allows the outputs to drive loads connected to a voltage higher than the 5 V logic supply, such as 12 V relay coils or 24 V indicator lamps. The open-collector configuration also allows outputs to be wire-ORed for simple logic combining.\n\nThe LS (Low-power Schottky) variant dissipates only 35 mW typical, compared to 215 mW for the original 74145 standard TTL variant. This 6x power reduction makes the LS variant practical for modern designs, especially when multiple decoder\/driver ICs are used in a system.\n\nThe SN74LS145 is one of the few remaining standard logic devices that serves a driving function rather than just a logic function. While CMOS logic families (74HC, 74LVC) have largely replaced TTL for logic functions, the 80 mA sink current and 15 V breakdown voltage of the 74LS145 are not easily replicated by standard CMOS outputs, which typically have only 4-8 mA drive and 5-6 V breakdown. This unique combination of decoding and driving capability keeps the 74LS145 relevant in specific applications.\n\nCommon applications include driving 7-segment displays (using two 74LS145 devices in a multiplexed configuration), driving Nixie tube displays (the 15 V breakdown voltage is sufficient for the cathode switching), driving relay banks for sequential control, and driving LED arrays for indicator panels.\n\nThe DR suffix denotes the SOIC-16 package with tape and reel (2500 units per reel). The SOIC package is preferred for automated SMT assembly, while the PDIP (N) package is available for prototyping and through-hole applications.","working_principle":"The SN74LS145DR operates as a combinational logic circuit that decodes a 4-bit BCD input into one of ten active-low output signals, using a network of inverters and NAND gates followed by NPN output transistors.\n\nInput Logic: The four BCD input lines (A, B, C, D) represent a decimal digit from 0 to 9. Input A is the least significant bit (LSB) and D is the most significant bit (MSB). The input coding follows standard BCD: 0000 = 0, 0001 = 1, 0010 = 2, ..., 1001 = 9. Input codes 1010 through 1111 (decimal 10-15) are invalid BCD values and result in all outputs being OFF.\n\nDecoding Logic: The device consists of eight inverters and ten four-input NAND gates. The four BCD inputs and their complements (generated by the inverter pairs) are connected to the NAND gates in a pattern that implements the BCD decoding truth table. Each NAND gate corresponds to one decimal output (0 through 9) and is wired to activate only when the BCD input matches the corresponding decimal value. For example, the NAND gate for output 0 receives inputs A-complement, B-complement, C-complement, and D-complement, so it activates only when all inputs are LOW (BCD 0000).\n\nInvalid BCD Handling: The NAND gate wiring inherently ensures that none of the ten NAND gates activates for input codes 1010 through 1111. This is because each output NAND gate requires a specific combination of true and complemented inputs that only matches a valid BCD value (0-9). For example, output 0 requires D=0, which is not satisfied for any code 1010-1111 (where D=1). Similarly, outputs 8 and 9 require D=1 with specific ABC patterns that do not match the invalid codes. This full decoding of valid input logic ensures that all outputs are OFF for invalid inputs, providing natural blanking.\n\nOutput Stage: Each of the ten outputs is an NPN transistor with an open-collector configuration. When the corresponding NAND gate output is LOW (the selected output), the NAND gate drives the base of the NPN transistor through a current-limiting resistor, turning the transistor ON. The transistor saturates, pulling the output pin LOW (close to GND) and sinking current through the load connected between a positive supply and the output pin. When the NAND gate output is HIGH (unselected outputs), the NPN transistor is OFF and the output pin is effectively open-circuited (high impedance), allowing the load to be pulled to the external supply voltage through the load itself.\n\nCurrent Drive: Each output transistor can sink up to 80 mA of continuous current. The transistor is designed with a saturated collector-emitter voltage (VCE(sat)) of approximately 0.7 V at 80 mA, so the voltage drop across the output transistor is relatively small even at maximum current. The output breakdown voltage (VCE(off)) is 15 V minimum, meaning the output can be connected to loads powered by up to 15 V when the transistor is OFF.\n\nPower Dissipation: The LS variant uses Schottky-clamped transistors in the internal logic gates, which prevents the transistors from entering deep saturation and reduces storage time. This results in a typical power dissipation of only 35 mW, compared to 215 mW for the standard TTL 74145 variant. The lower power dissipation also reduces the junction temperature rise, improving reliability in multi-IC applications.\n\nTTL Input Characteristics: The inputs are standard LS TTL, requiring 0.4 mA sink current at LOW level (0.8 V maximum) and negligible current at HIGH level (20 uA at 2.7 V minimum). One LS TTL input represents one unit load, so the 74LS145 inputs can be driven by any standard LS TTL output. The inputs are also compatible with CMOS logic (74HC, 74HCT) when appropriate pull-up resistors are used to ensure the HIGH level exceeds the 2 V minimum TTL threshold.","pin_description":"
| Pin<\/th> | Name<\/th> | Type<\/th> | Description<\/th><\/tr><\/thead> | ||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1<\/td> | A<\/td> | Input<\/td> | BCD input, least significant bit (LSB); TTL compatible input; represents the 2^0 digit of the BCD code; input current 0.4 mA max at LOW level; connect to BCD counter or logic output; one LS TTL unit load<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 2<\/td> | B<\/td> | Input<\/td> | BCD input, second bit; represents the 2^1 digit of the BCD code; same TTL input characteristics as pin A<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 3<\/td> | C<\/td> | Input<\/td> | BCD input, third bit; represents the 2^2 digit of the BCD code; same TTL input characteristics as pin A<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 4<\/td> | D<\/td> | Input<\/td> | BCD input, most significant bit (MSB); represents the 2^3 digit of the BCD code; same TTL input characteristics as pin A<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 5<\/td> | Output 0<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 0; active (LOW) when BCD input is 0000; sink current up to 80 mA; breakdown voltage 15 V; connect load between positive supply (up to 15 V) and this pin; when inactive, output is OFF (high impedance)<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 6<\/td> | Output 1<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 1; active when BCD input is 0001; same output characteristics as Output 0<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 7<\/td> | Output 2<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 2; active when BCD input is 0010; same output characteristics as Output 0<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 8<\/td> | GND<\/td> | Power<\/td> | Ground; 0 V reference; connect to PCB ground plane; provides the ground reference for internal logic and the emitter connection for the output transistors; must carry the total sink current from all active outputs<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 9<\/td> | Output 3<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 3; active when BCD input is 0011<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 10<\/td> | Output 4<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 4; active when BCD input is 0100<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 11<\/td> | Output 5<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 5; active when BCD input is 0101<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 12<\/td> | Output 6<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 6; active when BCD input is 0110<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 13<\/td> | Output 7<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 7; active when BCD input is 0111<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 14<\/td> | Output 8<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 8; active when BCD input is 1000<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 15<\/td> | Output 9<\/td> | Output<\/td> | Active-low open-collector output for decimal digit 9; active when BCD input is 1001<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 16<\/td> | VCC<\/td> | Power<\/td> | Positive supply voltage; 5 V nominal (4.75 V to 5.25 V); bypass with 100 nF ceramic capacitor to GND placed close to the pin; the supply powers the internal logic gates; output load current flows through the external load and the output transistor to GND (not through VCC)<\/td><\/tr><\/tbody><\/table>","application_scenarios":"
|