The LSM6DSLTR is an iNEMO 6DoF inertial measurement unit (IMU) from STMicroelectronics in an LGA-14 (2.5x3x0.83 mm) package. It integrates a 3D digital accelerometer (\u00b12\/\u00b14\/\u00b18\/\u00b116 g) and 3D digital gyroscope (\u00b1125\/\u00b1245\/\u00b1500\/\u00b11000\/\u00b12000 dps) with 16-bit output. Ultra-low power: 0.65 mA combo high-performance, 3 \u00b5A accelerometer-only low-power. Features 4 KB Smart FIFO, embedded pedometer\/step counter, significant motion detection, tilt function, free-fall\/wake-up\/6D interrupts. SPI and I2C interfaces with data synchronization. Rate noise density: 4 mdps\/\u221aHz. Supply: 1.71-3.6V (VDD), 1.62V min (VDD_IO). Temperature: -40C to +85C. ECOPACK2, RoHS compliant. Ideal for smartphones, wearables, IoT, and gaming.<\/p>","protected":false},"excerpt":{"rendered":"
The LSM6DSLTR is an iNEMO 6DoF inertial measurement unit (IMU) from STMicroelectronics in an LGA-14 (2.5x3x0.83 mm) package. It integrates a 3D digital accelerometer (\u00b12\/\u00b14\/\u00b18\/\u00b116 g) and 3D digital gyroscope (\u00b1125\/\u00b1245\/\u00b1500\/\u00b11000\/\u00b12000 dps) with 16-bit output. Ultra-low power: 0.65 mA combo high-performance, 3 \u00b5A accelerometer-only low-power. Features 4 KB Smart FIFO, embedded pedometer\/step counter, significant motion […]<\/p>\n","protected":false},"author":2,"featured_media":1875,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"footnotes":""},"categories":[13,42],"tags":[],"chip_brand":[142],"class_list":["post-1830","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-integrated-circuits-ics","category-sensors","chip_brand-st"],"acf":{"brief_explanation":"6DoF IMU, 3D accelerometer + 3D gyroscope, always-on, 0.65mA, LGA-14 (2.5x3mm)","date_code":"","package_case":"LGA-14 (2.5 x 3 x 0.83 mm)","in_stock":106206,"datasheet":"https:\/\/www.st.com\/resource\/en\/datasheet\/lsm6dsl.pdf","price":"$2.29 (1K+ pcs)","product_introduction":"The LSM6DSLTR is an iNEMO 6-degree-of-freedom (6DoF) inertial measurement unit (IMU) from STMicroelectronics, integrating a 3D digital accelerometer and a 3D digital gyroscope in a single compact system-in-package. It is designed for smartphones, wearable devices, gaming controllers, and battery-operated IoT applications where ultra-low power consumption and always-on motion sensing are critical.\n\nThe accelerometer supports full-scale ranges of \u00b12\/\u00b14\/\u00b18\/\u00b116 g with 16-bit output resolution and a sensitivity of 0.061 mg\/LSB at the \u00b12 g range. The gyroscope supports full-scale ranges of \u00b1125\/\u00b1245\/\u00b1500\/\u00b11000\/\u00b12000 dps with 16-bit output and a sensitivity of 4.375 mdps\/LSB at the \u00b1125 dps range. Both sensors feature excellent zero-rate stability: \u00b140 mg zero-g offset for the accelerometer and \u00b13 dps zero-rate level for the gyroscope at 25C.\n\nA standout feature is the ultra-low power consumption: only 0.65 mA in combo high-performance mode (both accelerometer and gyroscope active), and just 0.4 mA in combo normal mode. In accelerometer-only low-power mode at 1.6 Hz, the current drops to approximately 3 \u00b5A, enabling truly always-on motion detection with minimal battery impact.\n\nThe device includes a 4 Kbyte Smart FIFO that supports multiple operating modes (bypass, FIFO, continuous, continuous-to-FIFO, bypass-to-continuous, and dynamic mode). The FIFO can store sensor data, timestamp, and configuration data, significantly reducing the frequency of host processor read operations and enabling batch processing for further power savings.\n\nEmbedded processing features include a pedometer with step detector and step counter, significant motion detection, and tilt function. These functions operate independently from the host processor, enabling always-on context awareness with minimal system power. Standard interrupt functions include free-fall, wake-up, 6D\/4D orientation detection, and single\/double-click recognition.\n\nThe LSM6DSLTR supports both SPI (up to 10 MHz) and I2C (up to 1 MHz in fast-mode plus) serial interfaces, with a main processor data synchronization feature. An embedded temperature sensor provides ambient temperature measurement. Hard-iron and soft-iron correction capabilities are available for external magnetic sensor compensation when used in 9DoF sensor fusion configurations.\n\nThe LTR suffix denotes the LGA-14 plastic land grid array package in tape and reel format (5,000 units per reel), measuring only 2.5 x 3 x 0.83 mm. The analog supply voltage range is 1.71V to 3.6V, with an independent I\/O supply (1.62V minimum). The device is ECOPACK2, RoHS, and Green compliant, with an operating temperature range of -40C to +85C. The rate noise density in high-performance mode is just 4 mdps\/sqrt(Hz).","working_principle":"The LSM6DSLTR operates as a dual MEMS inertial sensor combining a capacitive 3-axis accelerometer and a capacitive 3-axis gyroscope with integrated signal conditioning and digital processing.\n\nAccelerometer Sensing Mechanism: The accelerometer uses a differential capacitive sensing principle. Each axis has a proof mass suspended by silicon springs. When acceleration is applied, the proof mass displaces relative to fixed electrodes, changing the differential capacitance. The capacitance change is proportional to the applied acceleration and is converted to a digital value by a sigma-delta ADC. The 16-bit output provides high resolution across all selectable full-scale ranges (\u00b12\/\u00b14\/\u00b18\/\u00b116 g). The sensitivity scales with the full-scale setting: 0.061 mg\/LSB at \u00b12 g, 0.122 mg\/LSB at \u00b14 g, 0.244 mg\/LSB at \u00b18 g, and 0.488 mg\/LSB at \u00b116 g. The accelerometer bandwidth and ODR (output data rate) are independently programmable from 1.6 Hz to 6.66 kHz.\n\nGyroscope Sensing Mechanism: The gyroscope uses a vibrating MEMS structure operating on the Coriolis effect principle. A proof mass is driven to vibrate at a resonant frequency. When angular rate is applied, the Coriolis force causes a displacement perpendicular to both the drive vibration and the rotation axis. This displacement is detected capacitively and converted to a digital angular rate measurement. The 16-bit output provides selectable full-scale ranges from \u00b1125 to \u00b12000 dps with sensitivity from 4.375 mdps\/LSB (\u00b1125 dps) to 70 mdps\/LSB (\u00b12000 dps). The gyroscope ODR is independently programmable from 1.6 Hz to 6.66 kHz.\n\nPower Mode Architecture: The LSM6DSLTR supports multiple power modes for each sensor independently. The accelerometer has four modes: Power-down, Low-power (reduced bandwidth, lowest current), Normal (standard performance), and High-performance (highest bandwidth, best noise). The gyroscope has three modes: Power-down, Normal, and High-performance (also called sleep-to-wakeup mode). In combo high-performance mode with both sensors active, total supply current is 0.65 mA. In low-power accelerometer-only mode at 12.5 Hz ODR, current is approximately 10 \u00b5A.\n\nSmart FIFO: The 4 KB FIFO buffer accumulates sensor data (acceleration, angular rate, temperature, timestamp) without requiring frequent host reads. In dynamic mode, the FIFO can be configured to accumulate data only when a specific event (e.g., significant motion) occurs, or to switch from bypass to FIFO mode upon a trigger. The FIFO supports watermark interrupts, overrun detection, and decimation (storing every Nth sample) to optimize buffer utilization.\n\nEmbedded Processing Functions: The pedometer uses accelerometer data to detect steps via peak-detection algorithms running in the sensor hardware. The step counter accumulates total steps. Significant motion detection identifies when the device transitions from stationary to mobile, enabling location-based services. The tilt function detects device orientation changes. All these functions operate autonomously, generating interrupts without host CPU intervention.\n\nSensor Synchronization: The LSM6DSLTR provides hardware timestamping and a data synchronization signal that can be routed to an external pin. This feature allows precise time-alignment of IMU data with external sensors (e.g., magnetometer, barometer) for sensor fusion algorithms, critical for applications like indoor navigation and augmented reality.\n\nHard\/Soft Iron Correction: The device includes registers for hard-iron and soft-iron offset correction values that are applied to the gyroscope output when fusing with an external magnetometer. This simplifies the host software burden for 9DoF sensor fusion implementations.","pin_description":"
| Pin<\/th> | Name<\/th> | Type<\/th> | Default Function<\/th> | Description<\/th><\/tr><\/thead> | ||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1<\/td> | SCL\/SPC<\/td> | I<\/td> | I2C Clock \/ SPI Clock<\/td> | I2C serial clock (SCL) or SPI serial clock (SPC); 5V tolerant when VDD_IO is present<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 2<\/td> | CS<\/td> | I<\/td> | Chip Select \/ I2C Enable<\/td> | SPI chip select (active low); when tied to VDD_IO, selects I2C interface; when driven low, selects SPI interface<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 3<\/td> | SDA\/SDI\/SDO<\/td> | I\/O<\/td> | I2C Data \/ SPI MOSI<\/td> | I2C serial data (SDA, bidirectional) or SPI serial data input (SDI); in 3-wire SPI mode, also functions as SDO<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 4<\/td> | SDO\/SA0<\/td> | I\/O<\/td> | SPI MISO \/ I2C Address<\/td> | SPI serial data output (SDO); I2C least significant address bit (SA0) when in I2C mode; set high or low to select I2C address<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 5<\/td> | SDI\/SDO<\/td> | I\/O<\/td> | SPI 3-wire Data<\/td> | Additional data pin for 3-wire SPI configuration; also used for routing in some configurations<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 6<\/td> | INT1<\/td> | O<\/td> | Interrupt 1<\/td> | Programmable interrupt output 1; can be configured for data-ready, FIFO watermark, step detection, significant motion, tilt, free-fall, wake-up, 6D\/4D orientation, etc.<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 7<\/td> | OCS<\/td> | I<\/td> | Offset Correction Select<\/td> | Offset correction input; used for hard-iron correction synchronization with external magnetometer<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 8<\/td> | INT2<\/td> | O<\/td> | Interrupt 2<\/td> | Programmable interrupt output 2; independently configurable from INT1 for different event combinations<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 9<\/td> | RES<\/td> | -<\/td> | Reserved<\/td> | Reserved pin; connect to GND or leave floating per datasheet guidance<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 10<\/td> | RES<\/td> | -<\/td> | Reserved<\/td> | Reserved pin; connect to GND or leave floating per datasheet guidance<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 11<\/td> | RES<\/td> | -<\/td> | Reserved<\/td> | Reserved pin; connect to GND or leave floating per datasheet guidance<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 12<\/td> | VDD_IO<\/td> | P<\/td> | I\/O Supply<\/td> | Independent I\/O supply voltage; 1.62V to VDD; allows I\/O level shifting to match host processor voltage<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 13<\/td> | GND<\/td> | G<\/td> | Ground<\/td> | Device ground; connect to system ground plane<\/td><\/tr> | ||||||||||||||||||||||||||||||||||||
| 14<\/td> | VDD<\/td> | P<\/td> | Analog Supply<\/td> | Analog power supply; 1.71V to 3.6V; decouple with 100 nF + 10 uF capacitors to GND<\/td><\/tr><\/tbody><\/table>","application_scenarios":"
|